← All notes
Engineering note

GaN PA Line-Up for 5G N79 and C-Band Phased-Array Radar: H4W1A1 + H4E1N1

Product spotlight
April 14, 2026

Building a PA chain for 5G N79 band or a C-band phased-array radar requires a power-amplifier line-up for adequate amplification from transceiver output to antenna. Here's how the H4W1A1 pre-driver and H4E1N1 final-stage PA work together in a simplified, single-supply GaN line-up.

Building a PA chain for 5G N79 band or a C-band phased-array radar requires a power-amplifier (PA) line-up for adequate amplification from transceiver output to antenna, without intermediate stages. Such a line-up requires an appropriately sized and impedance-matched pre-driver amplifier and a final-stage PA, designed for power budget, gain, simplified DC-DC conversion and linearity.

The Line-Up

H4W1A1 — Pre-driver
Frequency: 2–9 GHz · Gain: 26 dB · Psat: 0.3W · I/O: 50-Ohm · Package: QFN 4×5mm

H4E1N1 — Power Amplifier
Frequency: 4.4–5.5 GHz · Gain: 31 dB · Psat: 20W · I/O: 50-Ohm · Package: QFN 4×5mm

The line-up has a combined gain of 57 dB across 4.4 to 5.5 GHz and covers the transmit path from upconverter or DAC output — both of which are typically in the -10 dBm to -20 dBm range — through to the antenna input.

Signal Chain Interface

For a 5G small cell, the maximum input power required to drive the H4W1A1 + H4E1N1 line-up is around -15 dBm, which is similar to the power output of standard transceiver ICs or frequency upconverters, without requiring an intermediate amplification stage.

Linearity

For a 1×100 MHz 5G NR signal, the H4W1A1 + H4E1N1 line-up has an uncorrected ACLR of -32 dBc. This is essentially the uncorrected ACLR of the final-stage PA H4E1N1 and is a demonstration of the linearity of the H4W1A1 pre-driver chip in a line-up. DPD correction of the line-up easily meets -50 dBc, well beyond the 5G ACLR requirement of -45 dBc.

Bias Network

Both devices are built using the same GaN process, meaning they use the same drain voltage, VDD. All VDD supply pins across the line-up can be connected to a single regulator, further simplifying the supply network compared to a mixed-process line-up. A GaAs driver with a GaN final stage would require separate regulators and different supply voltages for each device.

5G NR versus C-Band Phased-Array Integration

The H4W1A1 + H4E1N1 line-up is well-suited for both 5G NR N79 band and C-band phased-array radar, with the same hardware and PCB. In a C-band phased-array radar, the H4E1N1 may run differently to the 5G NR application, depending on pulsed-signal characteristics such as duty cycle and pulse width. There is more than adequate headroom in terms of thermal impact and performance. A 5G implementation will include a DPD feedback path between the final-stage PA and the antenna, while a C-band radar implementation often does not require it.

HEAVISIDE GaN PA Portfolio

The H4W1A1 and H4E1N1 are part of the MILLIBEAM HEAVISIDE GaN PA portfolio and can be paired with MILLIBEAM's surface-mounted antenna-in-package products supporting C-band. Evaluation units and simulation models are now available.

The silicon behind this note

Designed in silicon. Proven in the field.

The parts discussed here are designed, characterised and shipped by MILLIBEAM. Browse the catalogue, filter by band and package, and request a datasheet.

Acknowledgement of Country

MILLIBEAM acknowledges the Traditional Custodians of the lands throughout Australia where we live and work today. We celebrate the diversity of Aboriginal peoples and their ongoing cultures and connections to land, sea and community. We pay our respects to the Elders both past and present and extend that respect to all Aboriginal and Torres Strait Islander peoples today.